TYRE PRESSUE SENSOR TPMS FOR FORD FOCUS FIESTA B-MAX C-MAX KUGS EV6T-1A180-DC

Upgrade your vehicle's TPMS system with this set of 1 pre-programmed tyre pressure monitoring sensor. These OE-replacement sensors provide accurate pressure readings and maintain your dashboard warning system. This pre-programmed tyre pressure sensor replaces one Ford TPMS sensor and sends pressure readings to the car. It is sold for the Ford Focus, Fiesta, B-MAX, C-MAX and Kuga, and the listing also covers the other Ford models below.

Features

• EV6T-1A180-DC
• EV6T1A180DC
• EV6T-1A180-DA
• 2036832
• 2318530
• Quantity: 1 sensor
• Rubber snap-in valve
• Pre-programmed

Compatibility

• Ford B-MAX (2012 onwards)
• Ford C-MAX (2015 onwards)
• Ford EcoSport (2013 onwards)
• Ford Fiesta (2013 onwards)
• Ford Focus C-MAX (2011-2015)
• Ford Focus (2014 onwards)
• Ford Ka (2016 onwards)
• Ford Kuga (2013 onwards)
• Ford Mondeo (2015 onwards)
• Ford Ranger (2012 onwards)
• Ford Transit Connect (2013 onwards)
• Ford Transit Courier (2014 onwards)
• Ford B-MAX (JK8) 2012-2017
• Ford C-MAX (DXA) 2011-2019
• Ford EcoSport (JK8) 2013-2019
• Ford F-150 (2015-2020)
• Ford Fiesta VI (2008-2019)
• Ford Focus III (2011-2018)
• Ford Ka+ (2014-2021)
• Ford Kuga (2013-2019)
• Ford Mondeo MK5 (2014-2020)
• Ford Ranger (2011-2021)
• Ford Tourneo Connect (2013-2021)
• Ford Tourneo Courier (2014-2021)
• Ford Transit Connect (2014-2021)
• Ford Transit Courier (2014-2021)

Installation

1. Remove the tyre, deflate it fully and take the old sensor off the wheel.
2. Fit the new sensor and tighten it to the torque recommended for that vehicle.
3. Reinflate the tyre, balance the wheel and refit it.
4. Drive for several minutes at 15 mph (24 km/h) or more so the sensor can register.
5. If the car does not see the sensor, run the TPMS relearn procedure. An OBD tool can write the new sensor ID if relearn does not finish.
6. Install the new sensor on the rim and tighten it to the manufacturer-recommended torque.
7. Drive the vehicle for several minutes at 15 mph (24 km/h) or more to allow the sensor to register automatically.
8. If your vehicle's ECU does not recognise the sensor, run the TPMS relearn procedure in the vehicle's settings.
9. As a last resort, use an OBD-II TPMS programming tool to force-write the new sensor ID to the ECU.

Notes

• Quantity: 1 pre-programmed TPMS sensor.
• 1 year warranty for manufacturing defects and sensor battery failure.
• Sensors usually register after a short drive. If the warning stays on, run the relearn procedure or write the sensor ID with an OBD tool.
• Compare the part number or measurement on your original part before ordering.
• If the tyre-pressure warning lamp stays illuminated after installation, check that tyre pressures are set correctly and adjust by deflating or inflating as needed.
• Ensure each sensor is installed at the correct torque and the seals are seated properly to prevent air leaks.
• Verify that the part number and radio frequency (MHz) match your original sensors.
• Clear any stored TPMS faults in the vehicle's ECU before driving.
• If warnings persist, swap the wheel with another position to see if the issue follows the sensor, helping to identify a defective unit.
• Sensors are pre-programmed for your vehicle; they usually self-register after installation. If your vehicle's ECU does not recognise the new sensor, run the relearn procedure and, if necessary, use an OBD tool to program the ID.
• This package includes 1 pre-programmed TPMS sensor.