Upgrade your vehicle's TPMS system with this set of 4 pre-programmed tyre pressure monitoring sensors. These OE-replacement sensors provide accurate pressure readings and maintain your dashboard warning system. This screw-in tyre pressure sensor replaces the original Toyota and Lexus TPMS unit for the part numbers in the title. The live compatibility list covers Camry, C-HR, Land Cruiser 200, Land Cruiser Prado and Lexus LS, and the existing description also names the other Toyota and Lexus models below.

Features

• 42607-48020
• 42607-02070
• 42607-F4020
• 4260702090
• PMV-E100
• PMV-C215
• TX-S162
• Quantity: 4 sensors
• Colour: black
• Material: metal and plastic
• Frequency: 433 MHz
• Screw-in sensor with a separate valve cap
• Pre-programmed, and the item specifics say no programming is required
• Suitable for front and rear wheels, left and right
• Country of origin listed as Japan

Compatibility

• Toyota Camry (_V7_) 2017-2024
• Toyota Corolla
• Toyota C-HR (_X1_) 2016-2024
• Toyota RAV4
• Toyota Land Cruiser 200 (_J2_) 2015-2024
• Toyota Land Cruiser Prado (_J15_) 2015-2024
• Toyota Highlander
• Toyota 4Runner
• Toyota Avalon
• Toyota Sienna
• Lexus ES
• Lexus LS (_F5_) 2017-2024
• Toyota CH-R

Installation

1. Deflate the tyre and remove it from the rim.
2. Remove the old sensor and fit the new screw-in sensor with the sealing nut.
3. Refit and inflate the tyre, then balance the wheel.
4. Drive at about 15 mph (24 km/h) for 10 to 15 minutes so the car can learn the sensor.
5. Remove the tyre, deflate it fully and unbolt the old TPMS sensor from the wheel.
6. Install the new sensor on the rim and tighten it to the manufacturer-recommended torque.
7. Reinflate the tyre, balance the wheel and mount it back on the vehicle.
8. Drive the vehicle for several minutes at 15 mph (24 km/h) or more to allow the sensor to register automatically.
9. If your vehicle's ECU does not recognise the sensor, run the TPMS relearn procedure in the vehicle's settings.
10. As a last resort, use an OBD-II TPMS programming tool to force-write the new sensor ID to the ECU.

Notes

• 42607-48020, 42607-02070 and 42607-F4020 are in the title and on the gallery overlay.
• 4260702090, PMV-E100 and TX-S162 are in the item specifics. PMV-C215 is printed on the sensor and is also in the reference list.
• The interchange field also writes 4260748020 and 426074-48020. Those are the same 42607-48020 number, so they are not listed again.
• Corolla, RAV4, Highlander, 4Runner, Avalon, Sienna, Lexus ES, RX, NX, UX, GX and LX are kept from the existing description. No extra year was added for those models.
• If the warning lamp stays on, check the tyre pressures and the valve seal, then repeat the relearn or register the sensor with a TPMS tool.
• Compare the part number on your original sensor before ordering.
• If the tyre-pressure warning lamp stays illuminated after installation, check that tyre pressures are set correctly and adjust by deflating or inflating as needed.
• Ensure each sensor is installed at the correct torque and the seals are seated properly to prevent air leaks.
• Verify that the part number and radio frequency (MHz) match your original sensors.
• Clear any stored TPMS faults in the vehicle's ECU before driving.
• If warnings persist, swap the wheel with another position to see if the issue follows the sensor, helping to identify a defective unit.
• Sensors are pre-programmed for your vehicle; they usually self-register after installation. If your vehicle's ECU does not recognise the new sensor, run the relearn procedure and, if necessary, use an OBD tool to program the ID.
• Includes a 1 year warranty covering manufacturing defects and sensor battery failure.
• This package includes 4 pre-programmed TPMS sensors (one for each wheel).